StudentShare
Contact Us
Sign In / Sign Up for FREE
Search
Go to advanced search...
Free

Replacing the Outer Vehicle Constant Velocity Joint - Assignment Example

Cite this document
Summary
The author of the paper will begin with the statement that the CV joint of a car is the Constant Velocity joint, attached to each end of a drive shaft. It is used in transferring torque to the steered wheel and accommodating up and down motions of suspension…
Download full paper File format: .doc, available for editing
GRAB THE BEST PAPER96.4% of users find it useful
Replacing the Outer Vehicle Constant Velocity Joint
Read Text Preview

Extract of sample "Replacing the Outer Vehicle Constant Velocity Joint"

The removal and replacement of the outer CV joint involve a number of steps and processes, with a wide range of tools and equipment’s involved. Step 1: Jacking and Removal of the wheel. Jack the vehicle off the ground by use of a jack, either scissor jack, bottle jack or trolley jack. This will create a clearance between the vehicle and the ground, giving the mechanic a working space. Remove the wheel by use of a wrench. And using a spanner, remove the axle nut. This is a large nut on the outside of the hub.

Step 2: Remove the lower control arm. The removal of the lower control arm from the ball joint and the hub assembly will enable the removal of the bolt from the shock and upper control arm. The tapping will facilitate the slipping out of the CV joint through the back. The axle nut should be put back halfway during this process to avoid damaging of the threads. Step 3: Remove the axle. The axle is now held by the inner CV joint. To remove it, you need to tap from behind. This will pry it out from the differential and it will pop out from the ‘C’ clip holding it.

Step 4: Remove the ball bearings. Put the CV axle in a vise by the shaft close to the inner CV or the U-Joint. Cut the boot clamps and make sure that your CV joint is not held by on by a clip that you can see on the shaft under the boot. If there is no clip, you will want to tap lightly on the outer CV joint and then give a few good hits to knock it off the shaft. The tools involved in this are 5 lb Sledge and hammer. Make sure you wear protective glasses since the grease may fly. If it does not come out, put the axle in a vise and try again.

If this goes in vain, use the hammer and break the cage to remove the ball bearings. This will expose the race, and then press the race off the shaft using the punch hammer. Cut the race in the direction of the splines on the shaft so that it does not affect the new joint going into the splines (Gilles, 2004). Step 5: Cleaning the Shaft. Cut away the old boot and clamps and clean shaft with Break clean. Step 6: Replacing the Boot. Put on the new boot and slide it to the inner out of the way.

Fill the CV joint with grease, and a little of it on the ‘C’ clip. Line the outer CV joint with the splines of the shaft and place the axle nut on the threads halfway to avoid damaging the threads. Step 7: Greasing the joint. Grease the top of the joint and slide the boot down the clamp, the larger clamp first. Remove any trapped air between the boot and the shaft by moving a screwdriver in between. Step 8: Installation of the Axle. The axle is now ready for installation. Use the removal procedure but this time, in the reverse way (Gilles, 2004).

Read More
Cite this document
  • APA
  • MLA
  • CHICAGO
(“How to successfully replace an outter vehicle CV joint Coursework”, n.d.)
How to successfully replace an outter vehicle CV joint Coursework. Retrieved from https://studentshare.org/engineering-and-construction/1637682-how-to-successfully-replace-an-outter-vehicle-cv-joint
(How to Successfully Replace an Outter Vehicle CV Joint Coursework)
How to Successfully Replace an Outter Vehicle CV Joint Coursework. https://studentshare.org/engineering-and-construction/1637682-how-to-successfully-replace-an-outter-vehicle-cv-joint.
“How to Successfully Replace an Outter Vehicle CV Joint Coursework”, n.d. https://studentshare.org/engineering-and-construction/1637682-how-to-successfully-replace-an-outter-vehicle-cv-joint.
  • Cited: 0 times

CHECK THESE SAMPLES OF Replacing the Outer Vehicle Constant Velocity Joint

Toyota: Dimensions of Organizational Structure Style

Toyota: Dimensions of Organizational Structure 1.... Introduction Throughout the history, Toyota Corporation has been demonstrating its capacity to make use forward thinking (Frost, 2011).... To illustrate, Toyota has not only established a top competitor image in North America but also has become the Global automotive in the international market by utilizing the strategies formulated from all its experiences throughout the years since 1937....
4 Pages (1000 words) Research Paper

Bullet Velocity

It is difficult to measure forces within the barrel but the velocity at which the bullet exits the barrel (muzzle velocity), can easily be calculated (Bruner et al, 2011), and is given in feet per second.... Bullet velocities are classified as below 1000 fps, 1000-2000 fps and above 2000 fps as low, medium and high velocity respectively.... (Wilson, 1997) (Wilson, 1997) Bullet velocity Initial/Internal Ballistics Pressure exerted on the bullet by the burning powder is given by Pressure=Force/Area Whereby: Area = base of bullet= diameter of barrel = constant Energy transmitted to the bullet thus depends on: 1....
3 Pages (750 words) Research Paper

Velocity sensors

Name: Instructor: Task: Date: velocity Sensors Abstract of Sensor A velocity sensor is a crucial tool that is used to determine the rate of change of position of an object.... The velocity sensor is based on the movement further from the starting point of the object.... Returning to the turning point means that the person has achieved zero velocity.... Maximizing velocity requires the individual to take efforts that maximize the amount displaced from their original positions....
3 Pages (750 words) Research Paper

Mine-Protected Vehicles

The hull has been verified adjacent to anti-tank mine blasts and soaring velocity projectile.... This vehicle is also fitted with an articulated arm.... Army, it also comes as a control vehicle.... The Cougar is a versatile, 4x2, 4x4 or 6x6 multi-purpose vehicles with a wide range of configuration to a large variety of mission requirements like mine-protected personnel transport vehicle.... ingo 2 is a light mine-proof vehicle based on the well-known commercial Unimog chassis by Daimler Chrysler....
2 Pages (500 words) Essay

Taking municipal vehicles home

Some of these employees drive these vehicles while drunkard, conduct their personal businesses, and even use them beyond the traditionally working According to Plaisance, it was recommended that city employees should be paying a weekly fee in order to enjoy the privilege of driving home in a municipal vehicle (Plaisance par.... Taking municipality vehicle's home is a major concern since it acts as an indirect fining to city residents....
5 Pages (1250 words) Research Paper

Light Source Voltage and the Velocity of a Solar Car

In practice, solar cars are never supplied as daily transportation, but are normally seen as primarily vehicles for The paper “Light Source Voltage and the velocity of a Solar Car" is a brilliant variant of a lab report on physics.... In attempts to gain insight concerning the operation of solar vehicles, an experiment is set to investigate the relationship between the light source voltage and the velocity of a solar car.... The objective of the experiment is to find out the effect of light source voltage on the velocity of a solar car....
2 Pages (500 words) Lab Report

Single-Molecule Force Spectroscopy

… @ 2009High-throughput single-molecule force spectroscopy and DNA: A Programmable Force Sensor for membrane proteinsIntroductionSingle-molecule force spectroscopy is majorly useful in solving the low efficiency in information acquisition during the @ 2009High-throughput single-molecule force spectroscopy and DNA: A Programmable Force Sensor for membrane proteinsIntroductionSingle-molecule force spectroscopy is majorly useful in solving the low efficiency in information acquisition during the measuring of the forces....
11 Pages (2750 words) Essay

Optimum Design Specification to Design a Hybrid Vehicle

For one to contrast the Si plans (i=1… 6), every one of Si contains a planned contrast that brings organization over transmitted energy current in spite of the rotary velocity of torque.... Combining a Continuously Variable Transmission to the structure, S2 is consequently essential to allow transformation torque for necessary output energy at a convinced angular shaft velocity.... This literature review "Optimum Design Specification to Design a Hybrid vehicle" discusses environmental and financial factors that make available a convincing motion to formulate clean, competent, as well as, sustainable vehicles in various countries....
11 Pages (2750 words) Literature review
sponsored ads
We use cookies to create the best experience for you. Keep on browsing if you are OK with that, or find out how to manage cookies.
Contact Us